Inconsistency in 9 mm bullets : correlation of jacket thickness to post-impact geometry measured with non-destructive X-ray computed tomography

Fundamental to any ballistic armour standard is the reference projectile to be defeated. Typically, for certification purposes, a consistent and symmetrical bullet geometry is assumed, however variations in bullet jacket dimensions can have far reaching consequences. Traditionally, characteristics and internal dimensions have been analysed by physically sectioning bullets – an approach which is of restricted scope and which precludes subsequent ballistic assessment. The use of a non-destructive X-ray computed tomography (CT) method has been demonstrated and validated Kumar et al., 2011); the authors now apply this technique to correlate bullet impact response with jacket thickness variations. A set of 20 bullets (9 mm DM11) were selected for comparison and an image-based analysis method was employed to map jacket thickness and determine the centre of gravity of each specimen. Both intra- and inter-bullet variations were investigated, with thickness variations of the order of 200 um commonly found along the length of all bullets and angular variations of up to 50 um in some. The bullets were subsequently impacted against a rigid flat plate under controlled conditions (observed on a high-speed video camera) and the resulting deformed projectiles were re-analysed. The results of the experiments demonstrate a marked difference in ballistic performance between bullets from different manufacturers and an asymmetric thinning of the jacket is observed in regions of pre-impact weakness. The conclusions are relevant for future soft armour standards and provide important quantitative data for numerical model correlation and development. The implications of the findings of the work on the reliability and repeatability of the industry standard V50 ballistic test are also discussed

Numerical and experimental studies of multi-ply woven carbon fibre prepreg forming process

Woven carbon fibre prepreg is being increasingly used in high-performance aerospace and automotive applications, primarily because of its superior mechanical properties and formability. A wide range of forming simulation options are available for predicting material deformation during the prepreg forming process, particularly change in fibre orientation. Development of a robust validated simulation model requires comprehensive material characterisation and reliable experimental validation techniques. This paper presents experimental and numerical methods for studying the fibre orientation in multi-ply woven carbon fibre prepreg forming process, using a double-dome geometry. The numerical study is performed using the commercial forming simulation software PAM-FORM and the material input data are generated from a comprehensive experimental material characterisation. Two experimental validation methods are adopted for fibre shear angle measurement: an optical method for measuring only the surface plies, and a novel CT scan method for measuring both the surface plies and the internal plies. The simulation results are compared against the experimental results in terms of fibre shear angle and the formation of wrinkles to assess the validity of the model

Simulation, modelling and development of the metris RCA

In partnership with Metris UK we discuss the utilisation of modelling and simulation methods in the development of a revolutionary 7-axis Robot CMM Arm (RCA). An offline virtual model is described, facilitating pre-emptive collision avoidance and assessment of optimal placement of the RCA relative to scan specimens. Workspace accessibility of the RCA is examined under a range of geometrical assumptions and we discuss the effects of arbitrary offsets resulting from manufacturing tolerances. Degeneracy is identified in the number of ways a given pose may be attained and it is demonstrated how a simplified model may be exploited to solve the inverse kinematics problem of finding the “correct” set of joint angles. We demonstrate how the seventh axis may be utilised to avoid obstacles or otherwise awkward poses, giving the unit greater dexterity than traditional CMMs. The results of finite element analysis and static force modelling on the RCA are presented which provide an estimate of the forces exerted on the internal measurement arm in a range of poses

Inconsistency of threat level in soft armour standards, correlation of experimental tests to bullet X-ray 3D images

Fundamental to any ballistic armour standard is the reference projectile that is to be defeated. Typically, for certification, consistency of bullet geometry is assumed. Therefore, practical variations in bullet jacket dimensions can have far reaching consequences. Traditionally, internal dimensions have been analysed by physically sectioning bullets – an approach which rules out any subsequent ballistic assessment. The use of a non-destructive X-ray Computed Tomography (CT) method was demonstrated in [1]. Now, the authors apply this technique to correlate bullet impact response to jacket thickness variations. A set of 20 bullets (9 mm DM 11) was selected to analyse both intra and inter bullet variations using an image based analysis method to map the jacket thickness and measure the centre of gravity. Thickness variations of the order of 200μm were found commonly across all the bullets along the length and an angular variation of up to 50μm was found in a few bullets. The bullets were subsequently impacted against a rigid flat plate and re-scanned. The results of the experiments are shown and compared to the un-deformed bullet jacket thickness variations. The conclusions are relevant for future soft armour standards and provide important data for numerical model correlation and development

Characteristics, accuracy and reverification of robotised articulated arm CMMs

VDI article 2617 specifies characteristics to describe the accuracy of articulated arm coordinate measuring machines (AACMMs) and outlines procedures for checking them. However the VDI prescription was written with a former generation of machines in mind: manual arms exploiting traditional touch probe technologies. Recent advances in metrology have given rise to noncontact laser scanning tools and robotic automation of articulated arms – technologies which are not adequately characterised using the VDI specification. In this paper we examine the “guidelines” presented in VDI 2617, finding many of them to be ambiguous and open to interpretation, with some tests appearing even to be optional. The engineer is left significant flexibility in the execution of the test procedures and the manufacturer is free to specify many of the test parameters. Such flexibility renders the VDI tests of limited value and the results can be misleading. We illustrate, with examples using the Nikon RCA, how a liberal interpretation of the VDI guidelines can significantly improve accuracy characterisation and suggest ways in which to mitigate this problem. We propose a series of stringent tests and revised definitions, in the same vein as VDI 2617 and similar US standards, to clarify the accuracy characterisation process. The revised methodology includes modified acceptance and reverification tests which aim to accommodate emerging technologies, laser scanning devices in particular, while maintaining the spirit of the existing and established standards. We seek to supply robust re-definitions for the accepted terms “zero point” and “useful arm length”, pre-supposing nothing about the geometry of the measuring device. We also identify a source of error unique to robotised AACMMs employing laser scanners – the forward-reverse pass error. We show how eliminating this error significantly improves the repeatability of a device and propose a novel approach to the testing of probing error based on statistical uncertainty

Radio Jet-Ambient Medium Interactions on Parsec Scales in the Blazar 1055+018

As part of our study of the magnetic fields of AGN we have recently observed a large sample of blazars with the Very Long Baseline Array. Here we report the discovery of a striking two-component jet in the source 1055+018, consisting of an inner spine with a transverse magnetic field, and a fragmentary but distinct boundary layer with a longitudinal magnetic field. The polarization distribution in the spine strongly supports shocked-jet models while that in the boundary layer suggests interaction with the surrounding medium. This behavior suggests a new way to understand the differing polarization properties of strong- and weak-lined blazars.Comment: LaTex; 10 pages; 6 figures; reference fix; to appear in ApJL, 518, 1999 June 2

Evaluating the capability of laser scanning to measure an automotive artefact : a comparison study of touch trigger probe and laser-scanning

Abstract: In the automotive industry dimensional quality control is an important part of the production process, often carried out using coordinate measuring machines (CMMs). However, CMMs used in conjunction with touch probes have a relatively low measurement speed. There is also a close link between the cost of measurement and the number of discrete points captured, leading to a trade-off between the number of points that can be measured and the measurement time. Laser scanners offer a faster alternative to touch probe measurement, but have certain limitations. A number of studies have considered the accuracy of laser scanning using small artefacts; however, little work has been done on the verification of on-CMM laser scanning systems for large volume, industry-relevant measurement applications. In this research, a nominal representation of a vehicle body was used and 104 standard features were measured. The results show that the laser scanning sensor and CMM used in this study would, for the majority of measurements, provide a level of accuracy and repeatability better than which is typically required by automotive manufacturers for body shell quality inspection applications

Moving towards in-line metrology : evaluation of a Laser Radar system for in-line dimensional inspection for automotive assembly systems

The increasing interest towards intelligent systems has led to a demand for the development of zero-defect strategies, with a paradigm shift from off-line and dedicated to in-line metrology with integrated robotic systems. However, a major barrier preventing the systematic uptake of in-line metrology is the lack of evaluation of system capability in terms of accuracy, repeatability and measurement time, when compared to the well-established coordinate measuring machine (CMM). In this study, a robotic Laser Radar (LR) solution is assessed in the context of automotive dimensional inspection of Body-In-White (BIW) applications. The objective is both to understand the effect of robot re-positioning error on measurement accuracy and repeatability and to compare measurement results against a CMM. Eighty-one surface points, six edge points, twenty-five holes and sixteen slots were selected from an industry standard measurement plan. Whilst LR exhibits a lower measurement accuracy than twin-column CMM, its repeatability is well within the specification limits for body shell quality inspection. Therefore, as a real-time in-line metrology tool, it is a genuine prospect to exploit. This research makes a significant contribution toward in-line metrology for dimensional inspection, for automotive application, for rapid detection and for correction of assembly defects in real time, with subsequent reduction of scrap and number of repairs/re-works

Evaluation of a multi-sensor horizontal dual arm Coordinate Measuring Machine for automotive dimensional inspection

Multi-sensor coordinate measuring machines (CMM) have a potential performance advantage over existing CMM systems by offering the accuracy of a touch trigger probe with the speed of a laser scanner. Before these systems can be used, it is important that both random and systematic errors are evaluated within the context of its intended application. At present, the performance of a multi-sensor CMM, particularly of the laser scanner, has not been evaluated within an automotive environment. This study used a full-scale CNC machined physical representation of a sheet metal vehicle body to evaluate the measurement agreement and repeatability of critical surface points using a multi-sensor horizontal dual arm CMM. It was found that there were errors between CMM arms and with regard to part coordinate frame construction when using the different probing systems. However, the most significant effect upon measurement error was the spatial location of the surface feature. Therefore, for each feature on an automotive assembly, measurement agreement and repeatability has to be individually determined to access its acceptability for measurement with a laser scanner to improve CMM utilisation, or whether the accuracy of a touch trigger probe is required

Jet opening angles and gamma-ray brightness of AGN

We have investigated the differences in apparent opening angles between the parsec-scale jets of the active galactic nuclei (AGN) detected by the Fermi Large Area Telescope (LAT) during its first three months of operations and those of non-LAT-detected AGN. We used 15.4 GHz VLBA observations of sources from the 2 cm VLBA MOJAVE program, a subset of which comprise the statistically complete flux density limited MOJAVE sample. We determined the apparent opening angles by analyzing transverse jet profiles from the data in the image plane and by applying a model fitting technique to the data in the (u,v) plane. Both methods provided comparable opening angle estimates. The apparent opening angles of gamma-ray bright blazars are preferentially larger than those of gamma-ray weak sources. At the same time, we have found the two groups to have similar intrinsic opening angle distributions, based on a smaller subset of sources. This suggests that the jets in gamma-ray bright AGN are oriented at preferentially smaller angles to the line of sight resulting in a stronger relativistic beaming. The intrinsic jet opening angle and bulk flow Lorentz factor are found to be inversely proportional, as predicted by standard models of compact relativistic jets. If a gas dynamical jet acceleration model is assumed, the ratio of the initial pressure of the plasma in the core region P_0 to the external pressure P_ext lies within the range 1.1 to 34.6, with a best fit estimate of P_0/P_ext=2.Comment: 4 pages, 3 figures; accepted for publication in the A&A Letters; table in electronic form can be extracted from the preprint sourc